Influence of repositioning guides' color and usage on precision in tooth color measurement with a clinical spectrophotometer.

BACKGROUND: Repositioning guides are commonly employed in clinical studies to ensure consistent tooth color measurements. Yet, their influence on measured color remains uncertain. OBJECTIVE: This study evaluated the impact of repositioning guides' color and usage on tooth color measurement using a clinical spectrophotometer. METHODOLOGY: In total, 18 volunteers participated in this study, in which the color of their upper left central incisor and upper left canine was measured with or without repositioning guides (control). The guides were made from pink, blue, or translucent silicone, as well as an acetate-based bleaching tray. Tooth color was measured in triplicates using a clinical spectrophotometer based on the CIELAB system. The standard deviations of these readings were used to estimate reproducibility, and color differences (ΔE00) between the measurements with guides and the control were calculated. RESULTS: Repositioning guides had a minimal effect on L* values and no effect on b* values. The use of pink silicone increased a* values, whereas blue or translucent silicone reduced them. Irrespective of the evaluated tooth, the lowest ΔE00 values were observed for the translucent silicone and bleaching tray. The usage of guides only affected data variability for the L* color coordinate. CONCLUSION: Using repositioning guides can significantly impact the precision of tooth color measurement with a clinical spectrophotometer.

Color discrepancy of single-shade composites at different distances from the interface measured using cell phone images.

Objectives: This study aimed to evaluate the impact of substrate color and interface distance on the color adjustment of 2 single-shade composites, Vittra APS Unique and Charisma Diamond One. Materials and Methods: Dual disc-shaped specimens were created using Vittra APS Unique or Charisma Diamond One as the center composite, surrounded by shaded composites (A1 or A3). Color measurements were taken with a spectrophotometer against a gray background, recording the color coordinates in the CIELAB color space. Illumination with a light-correcting device and image acquisition using a polarizing filter-equipped cell phone were performed on specimens over the same background. Image processing software was used to measure the color coordinates in the center and periphery of the inner composite and in the outer composite. The color data were then converted to CIELAB coordinates and adjusted using data from the spectrophotometer. Color differences (ΔE00) between the center/periphery of single-shade and outer composites were calculated, along with color changes in single-shade composites caused by different outer composites. Color differences for the inner composites surrounded by A1 and A3 were also calculated. Data were analyzed using repeated-measures analysis of variance (α = 0.05). Results: The results showed that color discrepancies were lowest near the interface and when the outer composite was whiter (A1). Additionally, Charisma Diamond One exhibited better color adjustment ability than Vittra APS Unique. Conclusions: Color discrepancies between the investigated single-shade composites diminished towards the interface with the surrounding composite, particularly when the latter exhibited a lighter shade.

Influence of a gray background and the illuminant on tooth shade selection.

STATEMENT OF PROBLEM: Visual shade selection in dentistry may be influenced by factors that include the background color and the illuminant. PURPOSE: The purpose of this clinical study was to evaluate the influence of using a gray background and a light-correcting device on visual shade selection. MATERIAL AND METHODS: Two experienced clinicians assessed the incisor color of 30 volunteers using the VITA 3D-MASTER shade guide. Visual analyses were carried out using or not (control) a gray background, with and without (control) a light-correcting device (Smile Lite). Furthermore, the use of a polarizing filter was evaluated. Data from a clinical spectrophotometer were defined as the standard instrumental analysis. The agreement and the similarity (based on the whitening indexes of tabs) were evaluated between instrumental and visual analyses. Statistical testing was conducted through ordinal logistic regression and repeated-measures ANOVA. The Shapiro-Wilk test was used to confirm the data distribution, and homogeneity of variance was assessed with the Levene test (α=.05) RESULTS: The use of Smile Lite resulted in lighter tabs than indicated by the instrumental analysis, and the opposite was observed in its absence. The polarizing filter did not affect the results (P>.05). For similarity, the illuminant improved the results (P<.001). The gray background reduced the differences between visual and instrumental analysis only in the absence of the Smile Lite (P<.001). CONCLUSIONS: The color similarity between visual and instrumental analysis improved with the use of a light-correcting device with or without a polarization filter. A gray background was useful only without the light-correcting device.

Effect of gingival barrier brands on operator perception, cervical adaptation, and patient comfort during in-office tooth bleaching: a randomized clinical trial.

BACKGROUND: Light-cured resins are widely used as gingival barriers to protect the gums from highly concentrated peroxides used in tooth bleaching. The impact of barrier brand on clinical outcomes is typically considered negligible. However, there is limited evidence on the effects of different brands on operator experience, barrier adaptation, and patient comfort. OBJECTIVE: This clinical trial assessed the impact of four commercial gingival barrier brands (Opaldam, Topdam, Lysadam, and Maxdam) on operator perception, adaptation quality, and patient comfort. METHODS: Twenty-one undergraduate students placed gingival barriers in a randomized sequence using blinded syringes. Photographs of the barriers were taken from frontal and incisal perspectives. After bleaching procedures, operators rated handling features and safety using Likert scale forms. Two experienced evaluators independently assessed barrier adaptation quality on a scale from 1 (perfect) to 5 (unacceptable). The absolute risk of barrier-induced discomfort was recorded. Data were analyzed using Friedman and Chi-square tests (α = 0.05). RESULTS: Opaldam and Topdam received the highest scores in most handling features, except for removal, which was similar among all brands. No significant difference was observed in barrier adaptation quality between the evaluated brands. Discomforts were mainly reported in the upper dental arch, with Maxdam having the highest absolute risk (35% for this arch and 24% overall). CONCLUSIONS: This study suggests that gingival barrier brands can influence operator perception and patient comfort. Opaldam and Topdam were preferred by operators, but all brands demonstrated comparable adaptation quality. CLINICAL TRIAL REGISTRATION: The study was nested in a randomized clinical trial registered in the Brazilian Clinical Trials Registry under identification number RBR-9gtr9sc.

Effects of enamel moistening and repositioning guide color on tooth whitening outcomes: A clinical trial.

This clinical trial investigated the effects of pre-application enamel moistening on the impact of a 37% carbamide peroxide whitener on tooth color changes and the influence of repositioning guide colors. Forty participants were randomly assigned to in-office tooth bleaching with either moistened enamel (experimental) or dry enamel (control). The whitener was applied for 45 min over two sessions. Tooth color was visually measured or assessed using a spectrophotometer with purple or green silicone guides. Tooth bleaching was assessed using CIE76 (ΔEab ) and CIEDE2000 (ΔE00 ) formulas and by whitening and bleaching index score changes. Moistening the enamel did not significantly affect tooth color. However, the guide color choice only impacted tooth color when measured instrumentally. At baseline, the green guide resulted in statistically significantly whiter teeth than the purple guide. Less pronounced differences in the b* coordinate between baseline and final measurements were found using the green guide. The green guide also produced lower ΔEab values and less change in indexes. In conclusion, moistening the enamel did not significantly impact tooth color changes. However, the repositioning guide color influenced the tooth bleaching measured instrumentally, except for ΔE00 .

Influence of repositioning guides' color and usage on precision in tooth color measurement with a clinical spectrophotometer

Abstract Repositioning guides are commonly employed in clinical studies to ensure consistent tooth color measurements. Yet, their influence on measured color remains uncertain. Objective This study evaluated the impact of repositioning guides' color and usage on tooth color measurement using a clinical spectrophotometer. Methodology In total, 18 volunteers participated in this study, in which the color of their upper left central incisor and upper left canine was measured with or without repositioning guides (control). The guides were made from pink, blue, or translucent silicone, as well as an acetate-based bleaching tray. Tooth color was measured in triplicates using a clinical spectrophotometer based on the CIELAB system. The standard deviations of these readings were used to estimate reproducibility, and color differences (ΔE00) between the measurements with guides and the control were calculated. Results Repositioning guides had a minimal effect on L* values and no effect on b* values. The use of pink silicone increased a* values, whereas blue or translucent silicone reduced them. Irrespective of the evaluated tooth, the lowest ΔE00 values were observed for the translucent silicone and bleaching tray. The usage of guides only affected data variability for the L* color coordinate. Conclusion Using repositioning guides can significantly impact the precision of tooth color measurement with a clinical spectrophotometer.

Impact XP-endo finisher on the 1-year follow-up success of posterior root canal treatments: a randomized clinical trial.

OBJECTIVE: To evaluate the clinical relevance of using the XP-endo Finisher as a supplementary tool to improve the success of root canal treatment of posterior teeth with apical periodontitis, as assessed by 1-year follow-up. METHODS: A randomized clinical trial was conducted with 92 posterior teeth with apical periodontitis. Root canal treatment was performed using a single reciprocating file, with or without the supplementary use of the XP-endo Finisher. The status of apical periodontitis was assessed using the periapical index (PAI) at baseline and 1 year follow-up. Changes on PAI indicated that the lesions were healed, healing, or not healed. Successful treatments were defined as healed or healing lesions without clinical symptoms. Chi-square analysis and logistic regression were used for data analysis (α = 0.05). RESULTS: There was no significant difference in the distribution of healing status between the XP-endo Finisher group and the control group (p = 0.690). The success rates were also similar, with 81% in the XP-endo Finisher group and 78% in the control group. However, gender had a significant impact on success rates, with higher rates observed in females. CONCLUSIONS: The use of the XP-endo Finisher file as a supplementary tool did not affect the success rate of root canal treatment in posterior teeth with apical periodontitis. The findings indicate that the XP-endo Finisher file has limited clinical relevance in improving treatment outcomes for root canal treatment in posterior teeth with apical periodontitis. CLINICAL TRIAL REGISTRATION: The study protocol was registered in the Brazilian Clinical Trials Registry under identification number RBR-76w7cj (June 19, 2018).

The role of interface distance and underlying substrate on the color adjustment potential of single-shade composites.

OBJECTIVE: This study assessed how the distance from the composite interface and the underlying chromatic substrate affect the color adjustment potential (CAP) of two single-shade composites. MATERIALS AND METHODS: Cylinder-shaped specimens were created using Vittra APS Unique (VU), Charisma Diamond One (DO), and a shaded (A3) composite. Some single-shade specimens were surrounded by the A3 composite, forming dual specimens. Color measurements of simple specimens were taken against a gray background using a spectrophotometer. All specimens were positioned at a 45° angle in a viewing booth under illuminant D65, and images were captured with a DSLR camera against gray or A3 backgrounds. Image colors were measured using image processing software and converted to CIELAB coordinates. Color differences (ΔE00 ) between the single-shade composites and the A3 composite were calculated. CAP was determined by comparing data from simple and dual specimens. RESULTS: No clinically significant differences were observed between color measurements obtained from images and the spectrophotometer. CAP was higher for DO compared to VU and increased as the distance from the composite interface decreased and when specimens were positioned against an A3 background. CONCLUSION: The color adjustment potential increased with decreased distance from the composite interface and against a chromatic background. CLINICAL SIGNIFICANCE: Achieving satisfactory color match in restorations using single-shade composites is crucial, and selecting an appropriate underlying substrate is essential. The color adjustment gradually decreases from the restoration margins towards its center.

Prevalence of lectures about dental esthetics and female speakers in three Brazilian conferences.

This study analyzed the prevalence of lectures involving esthetics in the scientific program of Brazilian dental conferences and the gender distribution of speakers. All lectures presented in three dental conferences (Bahia, São Paulo, and Goiás states) held from 2016 to 2020 were evaluated. Three investigators individually divided the lectures according to the specialties recognized by the Brazilian Federal Council of Dentistry (FCD) based on their titles. The lectures were also classified as involving or not esthetics, and the speaker`s gender was recorded. Descriptive statistical analyses were performed, and Chi-square tests assessed possible associations between factors. The words most cited in the titles of the lectures were "esthetic" (13.6%), "dentistry" (9.9%), and "treatment" (8.1%). Oral diseases were barely mentioned in the titles (up to 1.3%). The highest number of lectures was observed for the specialty of Restorative Dentistry (22.3%), followed by Prosthodontics (18.5%). Approximately one-third of lectures involved some aesthetic aspect, but this percentage ranged from 71.9 to 78.6% for the two specialties with more lectures. Regarding the speaker`s gender, the inequity was higher for lectures involving esthetics (81.6% of males) than for topics unrelated to esthetics (66.7%). More male speakers than females were observed for all specialties. The highest gender gap was observed for Pediatric Dentistry with 62.4% male speakers, although only 10.6% of FCD registered specialists were men. In conclusion, the Brazilian dental conferences analyzed seemed to favor offering lectures dealing with esthetic topics and male speakers.

Prevalence of lectures about dental esthetics and female speakers in three Brazilian conferences

Abstract This study analyzed the prevalence of lectures involving esthetics in the scientific program of Brazilian dental conferences and the gender distribution of speakers. All lectures presented in three dental conferences (Bahia, São Paulo, and Goiás states) held from 2016 to 2020 were evaluated. Three investigators individually divided the lectures according to the specialties recognized by the Brazilian Federal Council of Dentistry (FCD) based on their titles. The lectures were also classified as involving or not esthetics, and the speaker`s gender was recorded. Descriptive statistical analyses were performed, and Chi-square tests assessed possible associations between factors. The words most cited in the titles of the lectures were "esthetic" (13.6%), "dentistry" (9.9%), and "treatment" (8.1%). Oral diseases were barely mentioned in the titles (up to 1.3%). The highest number of lectures was observed for the specialty of Restorative Dentistry (22.3%), followed by Prosthodontics (18.5%). Approximately one-third of lectures involved some aesthetic aspect, but this percentage ranged from 71.9 to 78.6% for the two specialties with more lectures. Regarding the speaker`s gender, the inequity was higher for lectures involving esthetics (81.6% of males) than for topics unrelated to esthetics (66.7%). More male speakers than females were observed for all specialties. The highest gender gap was observed for Pediatric Dentistry with 62.4% male speakers, although only 10.6% of FCD registered specialists were men. In conclusion, the Brazilian dental conferences analyzed seemed to favor offering lectures dealing with esthetic topics and male speakers.

Resumo Este estudo analisou a prevalência de palestras envolvendo estética na programação científica de congressos de Odontologia brasileiros, e a distribuição do gênero dos palestrantes. Todas as palestras apresentadas em três congressos de Odontologia (CIOBA, CIOGO, and CIOSP) entre 2016 e 2020 foram avaliadas. Três avaliadores utilizaram os títulos das palestras para dividi-las entre as especialidades reconhecidas pelo Conselho Federal de Odontologia (CFO) do Brasil. As palestras foram também classificadas como envolvendo ou não estética, e o gênero do palestrante foi registrado. Análises estatísticas descritivas foram realizadas, e testes de Qui-quadrado avaliaram possíveis interações entre fatores. A palavra mais citada nos títulos das palestras foi "estética" (13,6%), seguido por "odontologia" (9,9%) e "tratamento" (8,1%). Doenças orais foram raramente mencionadas nos títulos (até 1,3%). O maior número de palestras foi observado para a especialidade de Dentística (22,3%), seguido por Prótese Dental (18,3%). Aproximadamente um terço das palestras envolviam algum aspecto estético, com porcentagens entre 71,9 a 78,6% para as duas especialidades com mais palestras. Em relação ao gênero do palestrante, a inequidade foi maior para palestras envolvendo estética (81,6% de homens) que para tópicos não relacionadas à estética (66,7%). Mais palestrantes do sexo masculino que feminino foram observados para todas as especialidades. A maior discrepância entre os gêneros foi observada para Odontopediatria, uma especialidade com 62,4% dos palestrantes do sexo masculino, embora apenas 10,6% dos especialistas registrados no CFO eram homens. Como conclusão, os congressos de Odontologia Brasileiros parecem preferir palestras abordando tópicos de estética e palestrantes do sexo masculino.

Background and surrounding colors affect the color blending of a single-shade composite.

This study evaluated the background and effect of surrounding colors on the color blending of a single-shade composite used in a thin layer. Disc-shaped specimens (1.0 mm thickness) were built with the Vittra APS Unique composite surrounded (dual specimens) or not surrounded (simple specimens) by a control composite (shade A1, A2, or A3). Simple specimens were also built with only control composites. The specimen color was measured against white and black backgrounds with a spectrophotometer (CIELAB system). The whiteness index for dentistry (WID) was calculated for simple specimens. Differences (ΔE00) in color and translucency parameters (ΔTP00) between the simple/dual specimens and the controls were calculated. The translucency adjustment potential (TAP) and color adjustment potential (CAP) were estimated based on the ratios between data from simple and dual specimens. The Vittra APS Unique composite showed higher WID values than the controls. No differences between ΔTP00_SIMPLE and ΔTP00_DUAL were observed for any of the shades. The composite shade did not affect TAP values. The lowest values of ΔE00_SIMPLE and ΔE00_DUAL were observed for shade A1 regardless of the background color. For the white background, ΔE00_SIMPLE values did not differ from those of ΔE00_DUAL for all shades. Only A1 showed ΔE00_DUAL values lower than ΔE00_SIMPLE when the black background was used. The highest modulus of CAP (negative values for the white background) was observed when shade A1 surrounded the Vittra APS Unique composite. The color blending ability of the single-shade resin composite used in a thin layer was affected by both the surrounding shade and background color.

Effectiveness of the pharmacological treatments for sialorrhea in patients with Parkinson's disease: a systematic review and network meta-analysis.

OBJECTIVES: The present systematic review and network meta-analysis of randomized control trials (RCTs) aimed to establish whether there are evidence-based differences in the pharmacological agents used to manage sialorrhea in patients with Parkinson's disease (PD). MATERIAL AND METHODS: The authors searched the databases: MEDLINE via PubMed, EMBASE, Scopus, Web of Science, and Cochrane Library for clinical trials. Unpublished trials were searched on clinicaltrials.gov and the Brazilian Clinical Trials Registry. Means and standard deviations of changes in the salivary flow or drooling reported by participants due to the interventions were recorded. RESULTS: The authors analyzed 13 RCTs. Compared to the placebo, types A and B of the botulinum toxin effectively reduced the salivary flow and the severity or frequency of drooling. However, the network meta-analysis did not differentiate between the botulinum toxin types. Ipratropium bromide and glycopyrrolate did not differ from the placebo. Indirect evidence showed that ipratropium had similar results to those obtained with both types of botulinum toxin. The CINeMA approach estimated the quality of the evidence as very low for all comparisons. CONCLUSION: The best treatment for sialorrhea in patients with PD is not fully elucidated yet. Therefore, more well-conducted randomized clinical trials are required to increase the level of evidence. CLINICAL RELEVANCE: There needs to be more evidence defining the best intervention to treat sialorrhea in patients with PD. However, botulinum toxin types A and B seem to reduce sialorrhea in patients effectively.

Effect of modeling liquids on resin composite roughness and color parameters after staining and toothbrushing.

This study evaluated surface roughness, color stability, whitening index, and opacity of different types of modeling liquids for resin composite coating after exposure to staining and toothbrushing. Disc-shaped resin composite (Vittra APS, FGM) specimens were fabricated and divided into four groups (n = 10 each): control group, Composite Wetting resin (Ultradent Products), Adper Scotchbond Multipurpose adhesive (3M ESPE), and Adper Universal adhesive (3M ESPE). Surface roughness (Ra) was measured using a rugosimeter, while color stability (∆E00), whitening index (WI), and opacity (%) were measured using a spectrophotometer. Assessments were made at four time points: after polishing (baseline, T1), after immersion in red wine for 24 h (T2), and after 5,000 (T3) and 10,000 (T4) cycles of toothbrushing. Scanning electron microscopy images were captured to analyze the scratches created. The data were statistically analyzed by two-way repeated-measures analysis of variance and Tukey's honestly significant difference tests (α = .05). Modeling with the Wetting resin resulted in higher surface roughness (p < 0.05) and low color stability, which were attributable to porosities. Higher color change values were observed in the control group after staining. Both adhesives showed the lowest mean ΔE00 values (p < 0.005). WI decreased after staining, except with the use of the Universal adhesive (p < 0.005). The lowest opacity values were observed at baseline for all groups (p < 0.005). The Universal and Scotchbond adhesives had lower surface roughness, better color stability, higher WI, and the lowest opacity values after staining with red wine and toothbrushing.

Effects of surrounding and underlying shades on the color adjustment potential of a single-shade composite used in a thin layer.

Objectives: This study aimed to evaluate the surrounding and underlying shades' effect on the color adjustment potential (CAP) of a single-shade composite used in a thin layer. Materials and Methods: Cylinder specimens (1.0 mm thick) were built with the Vittra APS Unique composite, surrounded (dual specimens) or not (simple specimens) by a control composite (shade A1, A2, or A3). Simple specimens were also built only with the control composites. Each specimen's color was measured against white and black backgrounds or the simple control specimens with a spectrophotometer (CIELAB system). The whiteness index for dentistry (WID) and translucency parameters (TP00) were calculated for simple specimens. Differences (ΔE00) in color between the simple/dual specimens and the controls were calculated. The CAP was calculated based on the ratios between data from simple and dual specimens. Results: The Vittra APS Unique composite showed higher WID and TP00 values than the controls. The highest values of ΔE00 were observed among simple specimens. The color measurements of Vittra APS Unique (simple or dual) against the control specimens presented the lowest color differences. Only surrounding the single-shade composite with a shaded composite barely impacted the ΔE00. The highest CAP values were obtained using a shaded composite under simple or dual specimens. Conclusions: The CAP of Vittra APS Unique was strongly affected by the underlying shade, while surrounding this composite with a shaded one barely affected its color adjustment.

Supplementary use of the XP-endo Finisher on postoperative pain in posterior teeth with periapical lesions: a randomized clinical trial.

OBJECTIVE: This study evaluated the effect of the supplementary use of the XP-endo Finisher on postoperative endodontic pain. METHODS: This study was a randomized clinical trial with a parallel design. Ninety-two posterior teeth with necrotic pulps and apical periodontitis were instrumented with a single file (Reciproc) in a reciprocating movement followed or not (control) by additional instrumentation with XP-endo Finisher. Postoperative pain was assessed 24 h, 48 h, 72 h, and 7 days after the endodontic treatment (single session) using a universal pain assessment tool. The pain level was scored as absent, mild, moderate, or severe. The occurrence of sealer extrusion and flare-up was also recorded. Data on postoperative pain were analyzed through chi-square analysis, and the odds ratio was adjusted using a logistic regression model (α = 0.05). RESULTS: Similar levels and risks of postoperative pain were observed for both interventions, regardless of the assessment time. Approximately half of the participants presented any postoperative pain in the first 24 h after the endodontic treatment, and this occurrence reduced by less than 20% after 72 h. The extrusion of root filling material was observed in 36% of cases, and no participant presented flared-up. CONCLUSIONS: The supplementary use of the XP-endo Finisher file did not affect the incidence or level of postoperative pain reported after the endodontic treatment of posterior teeth with periapical lesions. CLINICAL RELEVANCE: The supplementary use of the XP-endo Finisher did not affect postoperative pain following the endodontic treatment of posterior teeth using a single-file reciprocating system. CLINICAL TRIAL REGISTRATION: The study protocol was registered in the Brazilian Clinical Trials Registry under identification number RBR-76w7cj (June 19, 2018).

Background and surrounding colors affect the color blending of a single-shade composite

Abstract This study evaluated the background and effect of surrounding colors on the color blending of a single-shade composite used in a thin layer. Disc-shaped specimens (1.0 mm thickness) were built with the Vittra APS Unique composite surrounded (dual specimens) or not surrounded (simple specimens) by a control composite (shade A1, A2, or A3). Simple specimens were also built with only control composites. The specimen color was measured against white and black backgrounds with a spectrophotometer (CIELAB system). The whiteness index for dentistry (WID) was calculated for simple specimens. Differences (ΔE00) in color and translucency parameters (ΔTP00) between the simple/dual specimens and the controls were calculated. The translucency adjustment potential (TAP) and color adjustment potential (CAP) were estimated based on the ratios between data from simple and dual specimens. The Vittra APS Unique composite showed higher WID values than the controls. No differences between ΔTP00_SIMPLE and ΔTP00_DUAL were observed for any of the shades. The composite shade did not affect TAP values. The lowest values of ΔE00_SIMPLE and ΔE00_DUAL were observed for shade A1 regardless of the background color. For the white background, ΔE00_SIMPLE values did not differ from those of ΔE00_DUAL for all shades. Only A1 showed ΔE00_DUAL values lower than ΔE00_SIMPLE when the black background was used. The highest modulus of CAP (negative values for the white background) was observed when shade A1 surrounded the Vittra APS Unique composite. The color blending ability of the single-shade resin composite used in a thin layer was affected by both the surrounding shade and background color.

Effect of modeling liquids on resin composite roughness and color parameters after staining and toothbrushing

Abstract This study evaluated surface roughness, color stability, whitening index, and opacity of different types of modeling liquids for resin composite coating after exposure to staining and toothbrushing. Disc-shaped resin composite (Vittra APS, FGM) specimens were fabricated and divided into four groups (n = 10 each): control group, Composite Wetting resin (Ultradent Products), Adper Scotchbond Multipurpose adhesive (3M ESPE), and Adper Universal adhesive (3M ESPE). Surface roughness (Ra) was measured using a rugosimeter, while color stability (∆E00), whitening index (WI), and opacity (%) were measured using a spectrophotometer. Assessments were made at four time points: after polishing (baseline, T1), after immersion in red wine for 24 h (T2), and after 5,000 (T3) and 10,000 (T4) cycles of toothbrushing. Scanning electron microscopy images were captured to analyze the scratches created. The data were statistically analyzed by two-way repeated-measures analysis of variance and Tukey's honestly significant difference tests (α = .05). Modeling with the Wetting resin resulted in higher surface roughness (p < 0.05) and low color stability, which were attributable to porosities. Higher color change values were observed in the control group after staining. Both adhesives showed the lowest mean ΔE00 values (p < 0.005). WI decreased after staining, except with the use of the Universal adhesive (p < 0.005). The lowest opacity values were observed at baseline for all groups (p < 0.005). The Universal and Scotchbond adhesives had lower surface roughness, better color stability, higher WI, and the lowest opacity values after staining with red wine and toothbrushing.

Effect of surrounded shade and specimen`s thickness on color adjustment potential of a single-shade composite.

This study evaluated the effect of surrounded shade and specimens` thickness on the color adjustment potential (CAP) of a single-shade composite. The composite Vittra APS Unique was surrounded (dual specimens) or not (simple specimens) by a control composite (shade A1, A2, or A3). Simple specimens of the control composite were also confectioned. Opacity and whiteness index for dentistry (WID) were calculated for simple specimens. Color differences between the simple (ΔE*SIMPLE)/ dual specimens (ΔE*DUAL) and the controls were calculated. CAP was calculated based on the ratio between ΔE* SIMPLE and ΔE* DUAL. The tested composite presented lower opacity (53 to 62% vs. 80 to 93%) and higher WID (≈ 42 vs. 18 to 32) than controls. Irrespective of the specimens' thickness (1.0/ 1.5 mm), the lowest values of ΔE* SIMPLE (11.1/ 10.8) and ΔE*DUAL (7.2/ 6.1) were observed using the surrounding shade A1. The shade A3 yielded higher ΔE*SIMPLE (16.4/ 17.1) and ΔE* DUAL (11.3/ 12.3) than the A2 (ΔE*SIMPLE = 13.4/ 14.6; and ΔE* DUAL = 9.7/ 10.3). The specimen`s thickness significantly affected the CAP (0.35 and 0.44 for 1.0 and 1.5 mm, respectively) only for shade A1, which had the highest CAP values. The shade A3 resulted in higher CAP values (0.31) than A2 (0.27) when 1.0-mm thick specimens were used, but similar values were observed for 1.5 thick specimens (≈ 0.29). In conclusion, both surrounding shade and specimen thickness can affect the CAP of a single-shade resin composite.

Effect of surrounded shade and specimen`s thickness on color adjustment potential of a single-shade composite

Abstract This study evaluated the effect of surrounded shade and specimens` thickness on the color adjustment potential (CAP) of a single-shade composite. The composite Vittra APS Unique was surrounded (dual specimens) or not (simple specimens) by a control composite (shade A1, A2, or A3). Simple specimens of the control composite were also confectioned. Opacity and whiteness index for dentistry (WID) were calculated for simple specimens. Color differences between the simple (ΔE*SIMPLE)/ dual specimens (ΔE*DUAL) and the controls were calculated. CAP was calculated based on the ratio between ΔE* SIMPLE and ΔE* DUAL. The tested composite presented lower opacity (53 to 62% vs. 80 to 93%) and higher WID (≈ 42 vs. 18 to 32) than controls. Irrespective of the specimens' thickness (1.0/ 1.5 mm), the lowest values of ΔE* SIMPLE (11.1/ 10.8) and ΔE*DUAL (7.2/ 6.1) were observed using the surrounding shade A1. The shade A3 yielded higher ΔE*SIMPLE (16.4/ 17.1) and ΔE* DUAL (11.3/ 12.3) than the A2 (ΔE*SIMPLE = 13.4/ 14.6; and ΔE* DUAL = 9.7/ 10.3). The specimen`s thickness significantly affected the CAP (0.35 and 0.44 for 1.0 and 1.5 mm, respectively) only for shade A1, which had the highest CAP values. The shade A3 resulted in higher CAP values (0.31) than A2 (0.27) when 1.0-mm thick specimens were used, but similar values were observed for 1.5 thick specimens (≈ 0.29). In conclusion, both surrounding shade and specimen thickness can affect the CAP of a single-shade resin composite.

Resumo Este estudo avaliou o efeito da cor circundante e da espessura da amostra no potencial de ajuste de cor (PAC) de uma resina monocromática. O compósito Vittra APS Unique foi circundado (amostras duplas) ou não (amostras simples) com um compósito controle (cor A1, A2 ou A3). Amostras simples do compósito controle também foram confeccionadas. A opacidade e o índice de brancura para odontologia (IBO) foram calculados para as amostras simples. As diferenças de cor entre amostras simples (ΔE*SIMPLE) / duplas (ΔE*DUAL) e os controles foram calculados. PAC foi calculado baseado na razão entre ΔE* SIMPLE e ΔE* DUAL. O compósito testado apresentou menor opacidade (53 a 62% vs. 80 a 93%) e maior IBO (≈ 42 vs. 18 a 32) que os controles. Independente da espessura da amostra (1,0/ 1,5 mm), os valores mais baixos de ΔE* SIMPLE (11,1/ 10,8) e ΔE*DUAL (7,2/ 6,1) foram observadas quando a resina circundante era A1. A cor A3 resultou em maior ΔE*SIMPLE (16,4/ 17,1) e ΔE* DUAL (11,3/ 12,3) do que A2 (ΔE*SIMPLE = 13,4/ 14,6; e ΔE* DUAL = 9,7/ 10,3). A espessura das amostras afetou significativamente o PAC (0,35 e 0,44 para 1,0 e 1,5 mm, respectivamente) apenas para a cor A1, que teve os maiores valores de PAC. A cor A3 resultou nos maiores valores de PAC (0,31) que A2 (0,27) quando amostras de 1,0 mm de espessura foram usadas, mas valores similares foram observados para amostras de 1,5 mm (≈ 0,29). Como conclusão, tanto a cor circundante como a espessura das amostras podem afetar o PAC de um compósito resinoso monocromático.

Bleaching effect of violet LED of 405-410 nm on stained endodontically treated teeth.

AIM: To evaluate in vitro the whiteness index (WID) and the whiteness index variation (ΔWID), as well as the color stability of stained endodontically treated teeth after bleaching with violet LED (VL) and with hydrogen peroxide 35% (HP) associated or not to VL. METHODS: Twenty-four lower incisors were selected. The color was measured using a spectrophotometer at the following times: baseline, after staining, bleaching, and thermocycling, to determine the whiteness index and variation (WID and ΔWID). For the staining process, the teeth were immersed in human blood and centrifuged. After biomechanical preparation, the specimens were distributed into three groups (n = 8): control group (HP); violet LED (VL); and HP 35% + VL (HP+VL), and one session was performed for both bleaching procedures every week for three weeks, followed by thermocycling, where 10,000 cycles were performed. After color analysis, the data obtained were submitted to statistical analysis (RM ANOVA, p < 0,05). RESULTS: The staining of the teeth reduced the WID values for all experimental groups compared to baseline, and the bleaching protocols increased WID values, with the lowest WID values for group VL. There was no statistically significant difference after thermocycling for all groups compared to bleaching. Staining and thermocycling reduced the ΔWID values, and no difference was found between treatments at these assessment times. Bleaching increased the ΔWID values, with less pronounced changes in the VL group. CONCLUSION: VL used alone has a lower bleaching effect compared to the bleaching treatment with HP, whether or not associated with VL, and the color stability was observed for all groups.